Versions Compared

Old Version 3

changes.mady.by.user Gosho Genchev

Saved on

compared with

New Version 4

changes.mady.by.user Slavina Nikolova

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

This page provides a tutorial for manually creating fuel and burning effects for a fire simulation.

Overview

...

UI Text Box
sizemedium
typeinfo

This is an Intermediate Level tutorial. Even though no previous knowledge of Phoenix FD is required to follow along, re-purposing the setup shown here to another shot may require a deeper understanding of the host platform's tools, and some modifications of the simulation settings.

Section
Column
width40%

The instructions on this page will guide you in modifying a fire simulation to add fuel and burning effects. The emitter object will emit fuel which ignites and produces smoke.

The Burning Fuel with Smoke Quick Simulation button on the Phoenix FD Shelf will produce a similar but more refined result to the steps below. 

Column
width5%

 

Column
width55%60%

Image Modified 

 

 

Steps

 

...

Section
Column
width40%

Start by creating a new project from File → Project Window. 
Click the New button at the top right corner of the window and give it a name.

This is important because Phoenix FD stores the simulation data in the data directory of the currently selected project. You can manually point to a different project directory from the File → Set Project... dialog.

Column
width60%

...

Section
Column
width40%

Add a Phoenix FD Fire/Smoke Source.

Rename it to phx_fuel_source_01 and the generated set to phx_fuel_source_set.

Middle mouse drag the source_geo into the fuel source set.

Column
width60%

...

Section
Column
width40%

With the Fuel source selected, go to the Attribute Editor and disable Temperature and Smoke emission.

Instead, Enable Fuel.

Using Temperature and Smoke to generate fire and explosive effects is a perfectly valid approach. However, this tutorial is focused on setting up a simulation that uses Fuel to produce burning which in turn adds smoke and heat into the container. 

Column
width60%

 

...

 

Section
Column
width40%

Create a Phoenix FD Container and position it around the source geometry.

Reduce the Cell Size to 0.1.

Rename the automatically generated sets to phx_preview_set, phx_lgt_set and phx_sim_set.

Middle mouse drag the source geometry and the Phoenix FD fuel source into the sim set.

Column
width60%

...

Section
Column
width40%

Note that despite having a lot of fuel in the container, no reaction is taking place. We need to enable burning.

In the Fuel tab of the Simulator, select Enable Burning.

The burning process in Phoenix FD converts the fuel into smoke, releasing heat and increasing the volume. The amount of heat produced is controlled by the Energy parameter, and the volume growth is controlled by the Propagation parameter.

 

Note

The burning process consumes oxygen. The oxygen level is not entered directly. Instead, the oxygen level is calculated as complementary fraction up to 1.0 for fuel, smoke, and oxygen combined. As an example, if the fuel value is 0.3 and smoke is 0.2, then oxygen is automatically calculated as 0.5 to give a sum of 1.0 for all three values. 

In other words, you should be mindful of the amount of smoke produced by the simulation.

Column
width60%

Info

Energy - Specifies the energy released from burning a unit of fuel.

Ignition Temperature - Ignition temperature in degrees Kelvin. Keep in mind that the environment temperature is 300K.

Fuel Depletion - The rate at which the fuel burns out.

Smoke Amount - Multiplier for the amount of smoke produced during burning.

Smoke Threshold - When the oxygen is less than the fuel, this value controls how much of the burning fuel produces smoke. Higher values cause less of the burning fuel to produce smoke.

Propagation - Controls the propagation speed of the ignition front.

...

Section
Column
width40%

To ignite the fuel, you need a source of Temperature.

You could either add an additional Phoenix FD Fire/Smoke source and disable the emission of all channels but Temperature, or alternatively, you could use the same phx_fuel_source_01 node and enable Temperature emission there.

In this example, the Discharge, Temperature and Fuel parameters are animated such that Fuel is sourced into the simulation for the first 2 frames and then the Temperature emission starts.

Column
width60%

...